Description
hardware flow control. It is an ideal choice in the field of industrial automation.
(1) Use STEP7V5.2 configuration software and enter Hardware Configure to complete S7-300 PLC hardware configuration;
(2) Select S7-315-2DP as the main station system, import the GSD (device database) file of NPBA-12 into the STEP7 programming environment, and configure the software
to configure NPBA-12 with S7-315-2DP as the main station. DP online, and select the PPO type to use. This design uses PPO4 to set the site network address. In the Profibus
structure of the variable frequency drive device, ABB frequency converters use the Profibus-DP communication module (NPBA-12) for data transmission, which is
mainly periodic: the host reads the input information from the slave station and sends the output information back to the slave station. ,
so it is necessary to call two system function blocks SFC14 and SFC15 in the PLC main program to read and write these data to achieve communication control to
the frequency converter;
(3) Create a data block in the main PLC program for data communication with the frequency converter; establish a variable table for observing the real-time
communication effect.
4 Inverter operation settings
After the frequency converter and PLC are connected to a network using Profibus-DP fieldbus, in addition to programming in the PLC automation system,
appropriate parameter settings must also be performed on each frequency converter.
After the communication cable is connected, start the inverter and complete the setting of the inverter communication parameters.
4.1 Basic settings
(1) 51.01—Module type, this parameter displays the module model detected by the transmission device. Its parameter value cannot be adjusted by the
user. If this parameter is not defined, communication between the module and the drive cannot be established.
(2) 51.02—This parameter selects the communication protocol, “0” selects the Profibus-DP communication protocol.
(3) 51.03—This parameter is Profibu
The PPO type selected by s connection, “3” is PPO4, but the PPO type on the inverter should be consistent with the PPO type configured on the PLC.
(4) 51.04—This parameter is used to define the device address number, that is, the site address of the frequency converter. Each device on the Profibus
connection must have a separate address. In this design, the two frequency converters are stations 2 and 3 respectively. [1]
4.2 Connection of process parameters
The process parameter interconnection completes the definition and connection of the corresponding parameters of the NPBA-12 dual-port RAM
connector and the frequency converter, including the connection from the master station (PLC) to the frequency converter and the connection from the frequency
converter to the master station (PLC). Set the following connection parameters on the frequency converter.
(1) PZD value sent from PLC to transmission inverter
PZD1—control word, such as start enable, stop, emergency stop and other control commands of the frequency converter;
PZD2—frequency setting value of the inverter.
(2) PZD value sent from the transmission inverter to the PLC
PZD1—status word, such as alarm, fault and other inverter operating status;
PZD2—actual speed value, current actual value, etc. of the frequency converter.
5 Conclusion
After the inverter control system adopts the Profibus-DP fieldbus control mode, the entire system not only has strong reliability and is easy to operate, but also can
be flexibly modified according to process needs. After this system was applied in Jigang Baode Color Plate Co., Ltd., it has been running well and has provided a successful
example for the future automation equipment (network communication of different manufacturers) of the head office.
New technology from Swiss ABB Group: Complete car charging in 15 seconds
This technology can charge a car in 15 seconds
The Swiss ABB Group has developed a new electric bus technology that can complete vehicle charging in 15 seconds . No other company”s battery technology can achieve this performance.
ABB has developed a technology called “Flash Charging” that allows an electric bus with 135 passengers to charge at charging points along the route. The charging point has a
charging power of 400 kilowatts and is located above the vehicle. The charging point is connected to a moving arm controlled by a laser and can charge the car battery in 15 seconds. Its
minimal design will help protect the urban environment and surrounding landscape.
The idea behind this design is to give the electric bus enough power to travel to the next charging station after one charge. The end of the line will allow for long periods of full charging
, with the car able to travel longer distances on a full charge. In addition to faster charging times, the system uses a carbon-emission-free solution called
TOSA to obtain electricity from clean hydroelectric power stations.
ABB initially plans to use this technology between Geneva Airport and the Palexpo International Convention and Exhibition Center. If the test is successful
, it will be deployed to public transportation systems. This is more cost effective and environmentally friendly.
ABB Executive Chief Technology Officer Claes Rytoft said: “With flash charging, we can trial a new generation of electric buses for large-scale transportation
in cities. This project will provide greater flexibility, cost-effectiveness and flexibility.” Paving the way for a lower public transport system while reducing pollution and noise.”
9907-167 Digital regulator control
9907-164 505 Digital microprocessor
9907-149 Overspeed protection module
9771-210 Base module TRICONEX
9200-06-02-10-00 Two-wire sensor
9199-00003 Monitoring module
8602-FT-ST Field terminal
8521-EB-MT Bus interface module
8502-BI-DP Bus interface module
8440-1713/D Governor module
8440-1706-B Synchronizer module
8327-1600 Overspeed safety device
8202-HO-IS 8-channel analog input module
8201-HI-IS 8-channel analog input module
8200-1302 505D digital governor turbine control
8200-226 Servo valve driver
6445-001-K-N High performance microstep driver
6410-024-N-N-N Stepper driver
6410-009-N-N-N Pulse encoder
6189-RDT10C Graphic color display
6186M-17PT High performance industrial display
6181P-17A2MW71DC Integrated display industrial computer
6181P-15TPXP High performance model unit
6176M-17PT Allen-Bradley’s industrial display
05704-A-0122 Analog input module
05701-A-0329 Analog input module
05701-A-0302 Honeywell Single channel control card catalysis
5601-RIO-MCM Remote I/O adapter gateway
5517B Laser interferometer system
5466-316 Programmable controller
5370-CVIM Allen-Bradley vision platform
5302-MBP-MCM4MB+ Protocol driver
5204-DFNT-PDPMV1 Ethernet /IP to PROFIBUS
5136-PFB-VME Profibus interface card
5136-PFB-PCI Communication adapter module
5136-PFB Profibus interface card
04380A Pulse generator
4301-MBP-DFCM Master/slave gateway
4073 TRICONEX Control system
TRICONEX 3720 Digital input module
3625 TRICONEX Digital input module
3100-MCM Communication interface
3096-1000 radiometer Radiant flux
3000RX-8D4A-A-13-MM-ST Power board module
2711P-T12W22D9P Programmable logic controller
2711P-T12C4D8 Man-machine interface
2711P-T10C4D8 PanelView 6 Plus 1000 series terminals.
2711P-T10C4D1 1000 Operator Terminal
2711P-T10C4A9 6 The terminal provides the extension function
2711P-T6M5D Operator Interface Terminal
2711P-T6C5A Operator Interface Terminal
2711P-RDT15C Allen-Bradley display module
Reviews
There are no reviews yet.